Gates and gates for fence: only reliable solutions

The company « Summer fences  Moscow region has been installing fences in Moscow, the Moscow region and the Central region since 2006: during this period we have manufactured and assembled more than 200,000 gates and gates with sheathing from profiled sheeting, a metal europain, wooden fence  and mesh netting.

Reduced prices for gates and wickets for carpeting with corrugated or metal fences

Our special prices: gates swinging 3x2 m with installation - from 6500 rubles, wicket gate 1x1.8 m with installation - from 4050 rubles

Additional work

• Manufacturing of gates up to 5 meters wide, including with a built-in wicket door
• Installation of overhead or mortise locks
• Installation of the upper removable screed from the profile pipe section 60x40 mm, thickness 2 mm
• Installation of the bottom non-removable screed at a depth of 30 cm
• Painting of metallic elements with Tikkurila paint
• Pouring of supports with a sand-gravel mixture with a tamping vibroinstrument
• Concreting of supports

Minimum order: 30 running meters  or 40 000 rubles.

The way of installation of the gate and gate is selected taking into account the type of soil

Unlike competitors, we rarely offer our customers expensive work: concreting the pillars or deepening them below the depth of freezing. According to experience, in most areas of New Moscow and the Moscow region properly completed pillar stowage is more reliable and effective.

• When drilling holes in peat soil, sand or light sandy loam, it easily flattens. We backfill the holes with a sand-gravel mixture or small gravel in a mixture with the soil, then we ram the mixture with a vibroinstrument.
• In the soils of clay (clay, loam), which increase in volume at minus temperatures, the forces of lateral punching act on the tangential support, which can lead to a concussion of the concreted pillar together with the base. We select the problem ground to the depth of the support installation and replace it with a sandy-gravel mixture.

Door and gate gates: quality material of own production

• Metal fence Nova Lux: rectangular profile with reinforcement (8 ribs of rigidity), semicircular top, rolled edges, double-sided polyester color coating 25 microns
• Profiled sheeting C8, C20 colored with one-sided / double-sided polymer coating, sheet production NLMK
• Profiled sheeting C8, C20 galvanized steel NLMK (140 g / m2)
• Rabitz
• Wooden fence

We use roofing screws with a press washer

If the installation of corrugated board or metal fence on the frame is poor, the appearance of the new input group will be damaged in the first year of operation. At the fastening points of the sheet to the frame, the integrity of the polymer coating and the zinc layer is broken, which protects the steel from corrosion. When using standard self-tapping screws, the steel comes into contact with water at the edges of the holes, ugly rusty streams are formed on the profiled sheet or the euro-bar. The design of roofing screws with a press washer allows you to tightly press the head of the screw to the surface of the sheet and insulate the mounting hole from the aggressive external environment.

Rolling gates 4x2 m at the best price in the Moscow region

For a long time our company carried out orders for the production of gates and gates only as part of a general contract for the installation of the fence, but since 2013 they have created a separate subdivision that accepts orders for the design, production and installation of sliding gates in suburban areas and industrial facilities. Now we can order the sliding gates in our company not only by customers who are installing a new fence, but also by those who want to replace the old or worn out entrance group with a convenient modern solution.

We will manufacture and install an input group with a mechanical drive at a price of 59,000 rubles, with an automatic drive and a remote control (Italian automation Nice) - at a price of 89,000 rubles.

Beauty for many years

The metal gate, like the gate, is a necessary part of any fence. And the rest of the fence can be built from another material. And the addition of forging elements will make the wicket more attractive, while not disrupting the external aesthetic appearance.

They are intended for passage or passage for the perimeter of a fenced area. In this article we will describe how they are built.

Preparation for work

Before you start making, you need to decide which gate you want to put on your site. Beautiful wickets made of metal are obtained with forging elements. It is better to order them in a company that deals with such works, giving the dimensions of the future design and determining the choice of the proposed sketches - to make an order. Samples of gates made of metal and gates with elements of forging can be seen on the photo:

For metal pillars use or each column is poured with concrete separately. And under the metal gates and wickets installation is carried out with more thorough ramming under the rack, so that later there is no heeling of the pillars and your disappointment from the work done.

We weld the gate

• Wicket from metal, as a rule, of the same height as the fence itself. In some cases, a retreat from the top of the fence is fifty centimeters - this distance depends on the height of the fence. The width is chosen in view of the fact that you can go with a wheelbarrow or hold a motoblock, we'll take ninety-eight centimeters, as shown in the photo:

• Then we cut off two pieces of the profile pipe of the desired width by the bulgarian. They will go to the top and bottom of the future design. It will take another piece of pipe, equal to ninety centimeters. We weld it in the middle.
• Then we cut off the bulgarian two more pieces of pipe equal to one meter forty-two centimeters. They will go to the side of the structure.
• We proceed to the welding process. We put profile pipe  on a flat surface and welded together, by means of electric welding (photo below).

After we welded all the details, we got a rectangle with a crossbar in the middle sized ninety-eight by one and a half meters.

The next step is to weld the loops to the resulting frame. Loops are easier to buy, the price for them is not large, and this will facilitate the work, which is important.

We will use garage hinges for the gate. Installation:

• separate them into two halves;
• part with a pin welded to a metal gate;
• second to the fence post;

Note! Do not mistake, loops without a pin are welded to the gate.

• during welding, make sure that the hinges are flush with the profile pipe and are strictly parallel to the wicket;
• hammer the slag from welding to a clean seam;
• we wipe out welded seams with a grinding disc by the Bulgarian;
• we paint the gate with a primer against corrosion.

Now we begin to install our gate in the fence opening.

• First you need to weld the second part of the loops, to the post, making sure that they are located at the same distance as at the gate itself.
• We connect the loops among themselves and level the gate in the aperture.

So we set up the gate. Now it remains to attach the profiled sheet or weld, the profile pipe, depending on what your fence is made of.

Today, in low-rise construction, the garage sectional doors with a wicket are gaining popularity, they have an aesthetic appearance. And also do not affect the adjacent territory at work, which gives you the opportunity to use it for a flower bed or lawn.

The figure illustrates the principle of operation:

We brought only one modification of sectional doors. There are also those that rise up, but they are installed in front of the entrance to the premises. Such gates are now used in car washes, maintenance stations, as well as in private cottages.

Still there is one plus - you can install an electric motor and open the gate by pressing the button on the control panel. This will give you the opportunity to open and close the gate without leaving your home or car, for example, in rainy weather.

Does not violate the appearance

Instead of an afterword

In conclusion of our story, I would like to wish you success in your work. We hope that you have learned something useful from our article, and now you will not be difficult to do what you have in mind and choose the option you like and the gate. If anyone has any questions, you can see the video in this article.

Metal gates

To protect their homes, our ancestors used various kinds of  fences. To date, the tradition of obsozablivat their property is not only not lost, but also strengthened its position. New modern materials began to be used, fences and fences are not only protective, but also continue the decor of the site. But, what kind of fence can do without a gate. The gates for the cottage, as well as the fences are very important function. It is good, if they are chosen taking into account the material of the fence and other criteria that will allow them to be used for a long time.

Gates can be made of different materials  - Profiled sheet, forging or metal. Metal gates - one of the most popular types of gates, which are most often chosen by consumers.

Manufacturing of gates for cottages

Manufacturing of gates  The process is complex and time-consuming. It is almost impossible to implement it independently. Therefore, in order to get a high-quality result, you need to contact a specialized store that manufactures a gate. First of all, the master will make an exit to your site for measurements. Depending on the material from which your gate will be made, their cost, production time will vary.

Installation of the gate is carried out by a special team. Usually, after the installation, a warranty is provided for servicing this design, in the event of a breakdown, post-warranty service is provided. Thus, when choosing the quality materials from which the gate will be made, you can create not only a reliable protection of your site, but also decorate the territory of your site.

When infield  the door can be manufactured independently. For example, your dacha is fenced with a simple wooden fence or a mesh-netting. These options are very good in terms of the isolation of the territory and the designation of its borders, so the gates for dachas can also be made of wood or mesh-rabitsa. In this case, you need to have the skills to work with wood or metal and have a special welding equipment to carry out the installation of this design. Gates for cottages can also be installed with the help of specialists. Depending on the size of your budget, the material will be selected, from which they will be manufactured and installed.

Metal gates occupy a leading position among the protective structures, due to their high performance: they are durable and durable, resistant to wear and mechanical damage. In addition, modern equipment allows you to significantly diversify the appearance of products that can become not only a protection, but also an ornament of your home, suburban area. Our company offers professional production of functional fencing from profiled sheeting and sheet steel using decorative techniques in decoration. The prices for products include the whole range of services, with delivery and installation.

Metal gate with wicket door

For owners of private houses in Moscow, we offer a functional metal gate with a wicket, which is already built into the canvas and ready for use. This kind of fencing is convenient and reliable - we provide high-quality fixation of the canvas, install reliable locks, convenient handles for the most pleasant and safe use of the product. You can choose the appropriate sketch of the fence in our catalog at your discretion, and also order the development individual project, which will take into account your wishes for technical properties  and the appearance of the structure.

Metal gates for cottages

Dacha steel structures, manufactured and installed by our specialists, will effectively protect your territory from strangers. You can choose recoiling metal gates to give, if the free space near the fence is limited, as well as classic swinging structures, if space allows. With us, you can buy an original hedge that will not interfere with the penetration of sunlight, so your garden will not lack lighting. We offer a catalog with a photo that will allow you to evaluate the quality of our work and make the right choice.

Manufacturing of metal gates

In our company manufacturing metal gates  is carried out by specialists independently, without involving outside organizations. Thanks to this, we carefully monitor the quality of work at each stage, which significantly reduces the risk of marriage and allows us to give guarantees. The production process includes measurement, design in accordance with customer requirements, manufacturing. We offer sliding and swinging iron structures, with or without a wicket, for a summer residence or an apartment house. Individual approach allows us to meet the requirements of our customers as precisely as possible.