Dampness, and as a result, a specific smell, mold, dissatisfaction at home and sometimes with neighbors below due to the appearance of stains on the ceiling - these are the unpleasant consequences of constant condensation on the toilet cistern. The question of how to get rid of this phenomenon becomes urgent.

Why does condensation appear on the toilet tank?

It is harmful to health when the air in the apartment is dry, but high humidity also leads to not very good consequences. This may also cause the tank to sweat. This often occurs where clothes are dried indoors, there is a large aquarium, or lovers of indoor flowers, trying to create conditions for their green pets that are close to natural, constantly spray them.

The most common cause of condensation is high humidity in the apartment.

These reasons can be easily eliminated - you can install air dehumidifiers or take the laundry out to the balcony after washing. It is more difficult when there are leaks in the plumbing or heating systems, ventilation is poor. The most common reason is the continuous flow of water at a low temperature due to problems in the design of the drainage device or due to frequent drains. Condensation in these cases is the result of contact of warm room air with the constantly cooling surface of the drain tank.

Malfunctions of the interior of the toilet and their elimination

If water, even in a thin stream, flows freely into the toilet, then its volume in the tank must be continuously replenished. Hence the droplets of water on the surface and large water bills. The solution to the problem is to eliminate the leak. Sometimes replacing a worn rubber siphon membrane helps:

• drain the water completely from the tank;
• fix the lever in such a position that the hole is closed with a valve and no more water flows in;
• dismantle the siphon by disconnecting it from the lever;

First of all, you should eliminate possible tank leaks, if any.

• remove the worn membrane and replace it with a new one;
• return the siphon to its place and secure it;
• perform a test drain.

Attention: when purchasing a new membrane, check that the material and dimensions fully correspond to the old model, otherwise the leak will remain.

The reason may also be hidden in a faulty float, then perform the following actions:

• remove the float from the tank;
• pour water out of it;
• let dry;

Float repair

• seal the hole through which water enters;
• are installed in place.

If it is possible to buy a new float, then this option is better, because... the repaired part will still not last long. The problem can be solved even easier if the leak occurs due to the incorrect position of the float; to eliminate it, simply open the reservoir and return the lever to its normal position.

Faulty ventilation as a cause of condensation

A poorly functioning one can also cause the tank to sweat. But many apartment owners, trying to improve the appearance of the room, simply cover the ventilation holes with cladding. This should not be done; it is better to purchase beautiful decorative grilles specifically designed for this purpose.

To check if it works well, you need to do the following:

1. Light a lighter or match and bring it to the ventilation hole.
2. Look at the light. If it goes out or is drawn into the ventilation duct, then the ventilation system is working normally. When the position of the fire remains the same or the deviation is insignificant, the ventilation does not work.

Be sure to check the proper functioning of the ventilation in the bathroom

You can diagnose ventilation using another method - just bring it to ventilation grille paper. Its adherence indicates the normal functioning of the system, but if it falls, then measures are necessary to improve ventilation.

There are two ways to solve this problem:

1. Cleaning ventilation ducts.
2. Device, i.e. installing a fan on the exhaust duct. This is the most effective method removal of exhaust air.

Tip: To ensure fresh air flows into the toilet, leave a gap of approximately 2 cm between the bottom of the door and the floor, or install a door flap. It will let air in from the outside and at the same time block the penetration of odors from the bathroom into the apartment.

Other ways to eliminate condensation

Never a sweaty toilet

Not long ago, toilet models with a two-piece tank appeared on sale. The water in it is in an internal plastic tank and does not come into contact with the walls of the main vessel, therefore, condensation does not form. The solution is ideal, but the cost is confusing - it is several times higher than that of a toilet with a traditional tank.

Construction of a two-piece toilet cistern

Minimizing waste

The smaller the volume of water that goes down the drain, the greater the chance that there will be no condensation. There are toilets with a cistern equipped with a two-button mechanism. When one button is used, approximately 5 liters of water flows out of the tank, the other - about 7 liters. And in tanks with an Aquastop drainage system, one control button is built into the lid: with one press, water begins to pour out, and with a second press you can stop this process.

Two-button mechanism for flushing water

Insulation of the cistern

Some craftsmen independently isolate the walls of the tank from interaction with cold water. The modification is as follows:

• apply sealant to the bottom, around the holes for installing fittings;
• put the bottom in place;
• insert the inner liner, having previously applied glue to the sides;
• fill the vertical joint with silicone;

Insulated cistern

• treat the joint between the bottom and side walls with sealant;
• Allow at least a day to dry, cut holes for the reinforcement, and apply sealant to the edges;
• put everything in place.

Tip: to insulate the tank, you can use neoprene, foamed polystyrene and other materials.

Here are the main causes of fogging in the toilet tank and how to eliminate them. If you cannot eliminate condensation yourself, contact a professional.

How to get rid of condensation on a toilet tank: video

https://youtu.be/p8iH0UvDCOg

Reasons for the appearance of condensation on the tank: photo

Add site to bookmarks

• Kinds
• Choice
• Installation
• Finishing
• Repair
• Installation
• Device
• Cleaning

Why does the toilet cistern sweat?

The toilet tank is sweating. There is a lot of condensation, it begins to drip onto the floor, forms puddles, and since the ceilings in the houses are not at all airtight, it leaks to the neighbors below. Both you and they have dampness, which contributes to the appearance of unpleasant odors, mildew and mold. The ceiling, saturated with moisture, begins to gradually collapse, and someday a fragment of the ceiling may collapse on your neighbors, and a hole will appear in your floor.

Very often, the occurrence of condensation on the toilet cistern spoils not only a good mood, but also good relationships with neighbors below.

In addition, condensation appears on cistern, and on the pipes adjacent to it. If these pipes are steel, without an anti-corrosion coating (and in old houses this is exactly the case), then the pipes will begin to become covered with rust.

The toilet cistern sweats especially often in winter time. The reason for this is easily explained: the container receives water from the water supply, the temperature of which is only 3-5°C, but in the apartment the temperature is 10-15°C higher. The humidity of warm air is quite high, because of this, droplets of water (dew) will immediately appear on the drain tank, and it does not matter what kind of tank: ceramic, cast iron or plastic. To prevent the appearance of condensation or at least reduce it, you should look for the cause of its formation and try to eliminate it.

Causes of condensation on the drain tank

1. The main reason for the appearance of condensation is considered to be high humidity in the bathroom. And the cause of increased humidity in the toilet can be a seal that closes too tightly. Entrance door. To fix this, you can make holes in the door.
2. Another reason for the accumulation of dew on the drain tank may be a breakdown of the locking mechanism. Continuously flowing water lowers the temperature of the water in the drain tank. When the problem is corrected, the water temperature will increase and dew will stop forming.

Return to contents

Ways to eliminate condensation

To prevent the toilet cistern from sweating, you can install a mechanism with a double button toilet flush system. This makes it possible to use both all the water from the tank (6-7 liters) and part of it. This way you can reduce the drainage of water, which will simultaneously reduce water consumption and reduce condensation on the drain tank.

Return to contents

Checking ventilation ducts

Diagram of the main elements of the tank: 1 – float valve, 2 – bulb combined with overflow, 3 – draft, 4 – float, 5 – water level.

To eliminate humidity and make the air drier, you should clean the special ventilation holes that are available in any apartment. Chasing the beauty of the interior, many residents of houses cover these holes with different finishing materials(for example, wallpaper), but this cannot be done. To decorate ventilation windows, you can buy special decorative grilles of different colors, shapes and designs. Before installing these decorative grilles, you need to clear the ventilation ducts of debris. It is better to invite relevant specialists for this.

You can use another option: make additional ventilation - instead of a grille, install a fan that will start working when the light in the toilet is turned on. This will also partially solve the problem with condensation formation.

There can be many problems and malfunctions in the bathroom that provoke urgent repairs. But such a surprise as condensation on the toilet tank can become quite unpleasant and not everyone knows what to do with it. The problem can bring a large number of problems both with health and comfortable living. Among other things, the effects of condensation can destroy any repair.

Why is it formed?

Perspiration on the tank can form both in winter and in summer. The main reason is temperature difference. Cold water usually has a temperature of 3 to 6 ° C, and the ambient air temperature in the room can be several times higher. If we add here the conditions of high humidity in the room, then the walls will definitely be heavily covered with drops of moisture. In this case, the material from which the device is made will not play a role. Condensation appears on cast iron products, as well as plastic and ceramic ones.

The process is explained by the elementary laws of physics. The toilet tank sweats because, if there is a surface with a lower temperature, the water on it turns from a gaseous state into a liquid. It is almost impossible to completely remove this phenomenon, but it is possible to minimize it. To eliminate the problem, you will need to eliminate the factors that cause the formation of perspiration.

One of the reasons may be frequent flushing and complete emptying of the tank. In almost all modern toilets, the thickness of the walls of the container is insufficient to eliminate the influence of temperature changes. As a result, the surfaces cool quickly.

Rooms with high humidity are most susceptible to the influence of washing machines and places for drying clothes in the bathroom. In combined bathrooms, the phenomenon occurs after taking a hot bath and active evaporation of water.

How dangerous is the phenomenon?

High-quality plumbing fixtures have almost no elements susceptible to corrosion. As a rule, fasteners used during assembly are made of durable plastic or stainless steel. But not every manufacturer offers high-quality parts. Often, in pursuit of savings, parts are made of average quality, which are susceptible to the harmful effects of constant contact with water. Thus, condensation on the toilet can lead to the development of corrosion on the fasteners that secure the tank to the bowl.

In addition, when moisture accumulates on the tank, other troubles can develop. For example, defects in the drain mechanism, which contribute to a failure in the normal process of collecting water into the tank. This happens due to the fact that the drain valve is not able to hold water in the tank and it continuously flows in a thin stream in the bowl. The constant movement of liquid again provokes an increase in humidity in the room and a significant increase in water consumption.

In the case of a wall-mounted tank, flowing drops of condensate will leave unpleasant stains on the wall and contribute to the development of a favorable atmosphere for the development of mold.

Perspiration can flow down the walls onto the floor, creating unpleasant-smelling puddles. They will again increase the humidity in the room and create favorable soil for fungus. Flowing drops in contact with other metal surfaces (pipes, taps) will cause corrosion.

How to eliminate fogging?

Elimination of either high humidity in the room or elimination of temperature differences can mainly help. You can remove condensation from the toilet tank using one or more of the following actions.

Setting up the drain mechanism

First, you can try to repair/adjust the drain system. The accumulation of water on the walls of the tank can be caused by a malfunction of this unit. If the fit is loose drain valve water may constantly flow into the toilet. In this case, the tank will continuously fill and cool. In such a situation, the volume of condensing liquid can reach 1-2 liters per day.

The fight against evaporation will be more effective if you start by repairing the drain and shut-off valves. The functionality of all components should be checked and, if necessary, replaced with a new one. To quickly figure out the repair, we advise you to look.

Before installing a new mechanism, you need to check for lime deposits on the drain hole. If necessary, remove them and replace the rubber seals. To avoid deformation of the sealing gaskets, it is recommended to tighten the nuts not with wrenches, but with your hands, but with the maximum possible force.

Reducing the volume of drained water

You can try to overcome condensation on the drain tank by reducing the volume of the drain. Of course, with a large number of residents and continuous use of the bathroom, this will be difficult to achieve. However, the amount of water drained should be minimized if possible. To do this, you can use the partial release button. With absence similar system It is recommended to replace the outdated device with a modern one. It will help get rid of condensation and save a certain amount of water.

Elimination of temperature differences

You can combat condensation formations by heating the collecting water. If the supplied water is the same temperature as the air in the room, then drops will not accumulate on the surface of the tank. This can be done by connecting a system with instantaneous water heating that has a thermostat and creating proper thermal insulation of the pipelines. The temperature can be set within 20-25°C.

On the other hand, you can lower the air temperature in the bathroom. But not everyone will like such a plan of action.

Installing a dehumidifier

The device must be selected in accordance with the humidity level, room area and your budget. Based on the principle of operation, two types can be distinguished:

1. Absorption - a container filled with an absorbent substance that perfectly absorbs moisture. Silica gel is often used.
2. Condensation – cools the air, and excess moisture condenses and settles inside the device.

Creating high-quality ventilation

Protecting your tank from condensation should start with ensuring good ventilation. It is not uncommon that when repairing a private house/apartment, the ventilation openings are closed or simply not carried out Maintenance. However, this is a significant mistake, because It is this that can completely eliminate problems with toilet fogging.

Checking the operation of the ventilation can be done very simply: just hold a sheet of paper to the hole or bring a lit match and put it out. If there is sufficient draft, the hood is functioning normally. If there is no draft at all or it is weak, then the ventilation ducts should be cleaned.

One of the most simple ways solve the problem - install forced ventilation.

Installation of a special tank

Modern technologies have long begun to solve the problem under consideration. One of them is a double tank toilet. The modification looks like this: a plastic tank inside, and a familiar ceramic casing on the outside. Between ceramic and plastic container a gap has been created that ensures that the water temperature is maintained at the same values ​​as room temperature. Installation of such a system can clearly solve all issues with condensate deposition.

However, such double tanks have one significant drawback - their high price.

Internal thermal insulation

Buying an expensive cistern/toilet is not always advisable. You can solve the problem yourself. To do this, foamed polyethylene is placed inside the tank. Due to such thermal insulation, it is possible to reduce the temperature difference several times and eliminate changes.

Naturally, the situation with condensation on the tank needs to be corrected. Otherwise, the consequences may be unhappy. If you approach the solution comprehensively, the situation will definitely improve.

Modern toilets are comfortable and aesthetically pleasing, and the inside smells pleasantly of scented products. To make it comfortable to be in the bathroom, it requires special care. Do you agree?

The room must be constantly cleaned and problems, including the formation of condensation, must be eliminated in a timely manner. If water constantly flows down the outer surface of the tank, an unpleasant odor appears in the apartment over time, and the plumbing fixture loses its attractive appearance. appearance. Due to droplets of water constantly flowing from the surface of the cistern, puddles form on the floor, which must be wiped off in a timely manner. Of course, you can adapt some kind of container to collect water, and then remember to empty it of its contents in a timely manner.

To get rid of condensation on the toilet tank and avoid negative consequences, you need to find out why the tank in the bathroom is sweating.

The most common reasons for the formation of condensation on the tank are:

Temperature difference

As a rule, the air temperature in the bathroom is higher than the surface temperature of the tank, since the latter is constantly filled with cold water. In the bathroom, additional heat sources are often installed, for example, heated towel rails and heated floors, which makes the temperature difference even greater. This is felt especially well in the cold season.

Condensation forms on the tank of plumbing equipment due to the fact that the air temperature in the room differs from the temperature of the water in the toilet by about 15 degrees.

Therefore, the outer surface of the tank begins to fog up.

Malfunction in the drain mechanism

Often condensation appears when the drain tank is constantly leaking, which, as you know, most often occurs when the float valve breaks down. If this is the case, then the problem can be easily solved by purchasing a new valve.

Due to a faulty mechanism, cold water from sewer pipes flows continuously in the tank without having time to settle.

As a result of the movement of cold water flows, condensation appears. If there is a meter, the owner of the apartment will have to pay for the leakage.

Most modern plumbing models do not require “local” repairs, so manufacturers do not produce small spare parts for them.

In the event of a breakdown, you will have to purchase a set of shut-off valves. If you can identify faulty structural elements and make repairs at the site of the breakdown, you will be able to reduce the excessive consumption of cold water, which is important for housing with a meter.

You can solve the problem without plumbing skills with the help of a specialist.

If you are familiar with the working principle drain system, then you can carry out the repairs yourself, while saving on calling specialists.

Depending on the toilet model, there are two ways to solve the problem - replacing the shut-off valves or local repairs of failed structural parts.

Condensation forms at any water pressure, but the degree of fogging of the tank depends on the power of the pressure. To fix the problem, you must either replace the faulty parts.

Lack of ventilation

A well-functioning ventilation system is the main condition for maintaining an optimal level of humidity in the room. If the bathroom is poorly ventilated, numerous problems appear, including condensation on the drain tank. Checking the condition of the ventilation holes To reduce the level of air humidity, you need to adjust the ventilation of the bathroom. Each apartment has special ventilation “windows” that provide air circulation.

In pursuit of the beauty of the interior, some residents seal these holes with finishing materials, which, of course, is unacceptable. To disguise ventilation windows, you need to buy decorative grilles that are specifically designed for this purpose. They can be selected by color, shape, and design. Before installing decorative grilles, clear the ventilation ducts of debris.

Air ventilation in the room can be organized even more efficiently if you connect a forced ventilation system. To calculate the power of the ventilation system, you must contact specialists. After assessing the condition of the bathroom and the intensity of its use, professionals will give recommendations on the choice of equipment.

If your toilet cistern is sweating, you need to urgently check the serviceability of the ventilation system in the bathroom.

You need to bring paper, a candle or a lighter to the ventilation grille. The system works fine as long as the paper sticks and the flame burns evenly. If paper falls or the flame goes out, then urgent measures must be taken to restore ventilation.

You can solve the problem of constant condensation in the following ways:

• Cleaning ventilation ducts.
• Installing an additional fan on the exhaust duct.
• An effective option for getting rid of exhaust air and obtaining a clean influx is to leave a gap 2 cm high.

Video: HOW TO GET RID OF CONDENSATE

Double wall cistern

Manufacturers of modern toilets are aware of the problem of condensation and offer their effective solution. The latest toilet models are being produced with an improved cistern design that prevents them from “crying.”

In these models, an additional plastic container is inserted inside the tank, the walls of which do not come into contact with the ceramic surface of the product. As a result, its temperature is always constant and equal to room temperature. This constructive solution allows you to solve the problem once and for all. However, for many buyers, these models still remain inaccessible at a cost that is several times higher than the price of conventional toilets.

pasting the internal walls of the tank with heat-insulating material

Some amateur craftsmen try to isolate the walls of the tank from the effects of cold water using thermal insulation materials, which are glued to them on the inside of the container.

However, this technology does not completely solve the problem of condensation.

If you still can’t afford expensive “no-crying” models, then try installing forced ventilation.

Even a simple fan, inserted into the ventilation window and turned on when the light is turned on in the bathroom, will solve the problem of condensation on cold surfaces. If the toilet cistern continues to sweat after this, call specialists to install more powerful ventilation systems.

Buying a dehumidifier

Another solution to the current problem of high humidity in the bathroom is to purchase a dehumidifier.

The principle of operation of the electrical appliance: a powerful fan directs a flow of moist air into a special cooling chamber, in which the process of condensation of moisture occurs and its separation into a special container. Then the dried air is heated and successfully returned to the bathroom.

How to remove condensation on a toilet cistern

A modern bathroom boasts practicality, convenience and comfort. If you care for your toilet properly, its appearance and functionality will last longer. But when fogging occurs on the toilet tank, this can lead to damage to the plumbing equipment, the appearance of foreign odors and the formation of black mold. How to deal with leaks and eliminate the cause completely?

When, it is necessary to identify the original cause of the appearance. Usually it is high level humidity in the room. To normalize this indicator, it is necessary to determine the reasons for the increase in level.

1. Faulty pipes or plumbing fixtures. Such breakdowns must be eliminated as soon as possible, since ignoring them can only aggravate the situation. Under the influence of moisture, pipes are exposed to corrosion, which leads to unnecessary leaks and flooding of neighbors.
2. Drying large volumes of laundry. This is true for large families and small spaces. In this case, it is recommended to dry things on the balcony (if there is one), as well as in the yard or in a separate room.
3. Poor quality ventilation system. Because of. That ventilation does not perform its functions properly, the air in the room does not have time to renew itself in time. Why does the room not dry out well enough?
4. The most common cause of toilet sweating can be considered a breakdown inside the tank itself. As a result, cold water enters constant mode, not having time to warm up to room temperature. That is why the tank begins to sweat.
5. There is a large amount of vegetation in the house that requires moisturizing procedures. Also, the presence of an aquarium affects the increase in humidity levels in the room. This reason can be eliminated by installing an air dehumidifier.

A striking example of fogging of the toilet cistern

Ways to eliminate condensation

The appearance of dampness, mold and unpleasant odor is far from full list consequences of fogging on the toilet cistern. To resolve these shortcomings, it is necessary to take a number of measures to improve the functionality of the premises.

Reducing water consumption

Since in large families the toilet is used quite often, you should reduce the amount of liquid flushed by adjusting the amount of water supplied. An easier solution to this problem is to purchase a new toilet with a flush that can be automatically adjusted. Also, toilet cisterns with an improved water drainage system are available for sale. When you press the button for the first time, the water is drained, and when you press it again, the process stops.

Improvement of the ventilation system

Poor ventilation causes many problems: respiratory diseases, insufficient oxygen, unpleasant odors, indoor humidity.

In order to check the functionality of the air ducts, just hold a sheet of paper to the ventilation hole. In this way you can check the quality of the system. If it malfunctions, the walls and floor may become covered with drops of water and fogging, which in turn can lead to the formation of fungus.

Forced ventilation

Installing forced ventilation helps solve the problem of condensation on the toilet cistern. Many consumers, wanting to decorate the room, close the ventilation hole. This should not be done under any circumstances! For such purposes, you can turn your attention to decorative grilles that cover the unesthetic appearance of the hole. At the same time, maintaining normal air circulation in the toilet room. Another solution could be to install a fan that starts when the lights in the room are turned on. And of course, the simplest option would be to leave the door to the restroom slightly open in the absence of visitors.

Change in water temperature

Fogging on the drain tank is formed as a result of the difference in the temperature of the water and the room. Typically, it varies from ten to fifteen degrees Celsius. By minimizing this difference, you can partially get rid of condensation.

To do this, you need to: insulate the pipeline, change the water source from cold to hot, or install a water dilution system.

Insulation of the drain tank

An example of insulating a toilet cistern with foamed polyethylene

You can insulate the drain tank by placing it in plastic construction at a distance of no more than two to three millimeters from each other. Between which you need to install gaskets. This will create a tank-within-a-tank system. When working, it is worth considering that the thickness of the material used should not exceed one centimeter, since otherwise it will not fit in the tank. required amount water. When installing insulation, you can use available means: sealant, glue and polyurethane foam. It is worth remembering that this work is carried out only after the water is completely shut off and the tank is free of all moisture.

Repair of cistern structure

If a breakdown of the drain tank structure occurs, you need to pay attention to the elasticity of the bulb, the quality of the rubberized elements, and the functionality of the shut-off valve. It is best to replace a used part rather than try to upgrade it yourself. Otherwise, such amateur activity can lead to uncontrolled drainage of water into the sewer, as a result of which the formation of condensate can increase to two to three liters per day.

Before installation new system, you should pay attention to several details: if the nuts are made of plastic, then they must be tightened by hand; Do not connect some parts too tightly, this can lead to premature wear of the structure; The drainage mechanisms must be located in the tank in such a way as to prevent accidental contact with its walls.

Drain control

To reduce the volume of water drained, it is enough to purchase a newer tank model. If this option is not possible, then the drain unit can be adjusted manually by independently adjusting the valve mechanism.

In addition, installing a double drain button can help solve the problem. In which, pressing one of them will mean draining the water, and the second will mean stopping the current process.

Home microclimate

To normalize the operation of the drainage system, you will need to start by upgrading the home microclimate. Since fogging on the toilet cistern may be a consequence of poor ventilation in the apartment. More specifically, exhaust air does not leave the room, but lingers, warms up and accumulates, settling on the surfaces of walls and plumbing. If replacing the old air duct is not possible, then the ventilation of the room should be controlled. Moreover, the restroom is a haven for various types of bacteria. There is no need to improve the conditions for their harmonious existence and reproduction.

Sweating toilet tank is a common problem for many apartment owners. Sometimes, in search of a solution, the owners correct a number of other possible consequences. Thus, improving your home. If condensation on the tank dries quickly, and its formation is infrequent, then in such a situation there is no reason to panic. Since the use of radical measures is not required.

Useful videos on the topic